How Many Decking Boards Do I Need?
16 November 2026 · 6 min read
If you are asking how many decking boards do I need, you will need four basic measurements: the deck length, deck width, board width and intended gap between boards. Once you have these, a straightforward calculation gives you the number of full-length boards required. You should then add an allowance for cuts, defects and mistakes.
This guide covers the maths for common board widths and includes a worked example. It is intended for planning materials only. K C Fencing and Timber Ltd supplies decking and other timber products but does not fit or install them.
What you need to measure
Start by measuring the finished deck area in metres. Measure the length and width at more than one point, particularly if the space is beside a house, wall or existing structure. Do not assume that every edge is perfectly square.
You will need to record:
- Deck length: the distance the boards will run, unless you plan a different layout.
- Deck width: the distance that will be covered by rows of boards.
- Board width: use the finished face width, not a rough or nominal size.
- Expansion gap: the space you intend to leave between adjacent boards.
- Available board lengths: these affect joints, offcuts and total waste.
It is sensible to sketch the deck and mark which way the boards will run. The chosen direction can alter the quantity because available lengths may suit one orientation better than another.
The basic decking board calculation
For a simple rectangular deck where each board runs across the full deck length, calculate the coverage width of one board by adding its face width and the planned gap.
Coverage per row = board width + gap.
Then divide the deck width by that figure:
Number of rows = deck width ÷ coverage per row.
Use the same unit throughout. The easiest approach is to convert the deck width into millimetres before dividing it by the board-and-gap measurement in millimetres. Always round the answer up to the next complete board.
This simple method slightly overstates the final outer gap because there is one fewer gap than there are boards. That normally gives a useful small margin. For closer planning, use this exact calculation:
Number of boards = (deck width + one gap) ÷ (board width + one gap).
Round up to a whole board. Remember that calculations do not replace checking the actual product dimensions and the spacing recommended for that product.
Coverage for common decking board sizes
Decking profiles vary, so confirm the finished width before ordering. As a quick guide, the following examples show approximate rows per metre when a 5mm gap is used:
- 95mm-wide board: 95mm + 5mm gives 100mm coverage, or about 10 rows per metre.
- 120mm-wide board: 120mm + 5mm gives 125mm coverage, or about 8 rows per metre.
- 125mm-wide board: 125mm + 5mm gives 130mm coverage, or about 7.7 rows per metre.
- 145mm-wide board: 145mm + 5mm gives 150mm coverage, or about 6.7 rows per metre.
These figures are planning guides rather than fixed specifications. Timber dimensions can vary slightly, and spacing may need to account for moisture content and expected movement. Check the measurements of the decking boards you intend to buy before finalising your order.
Board thickness does not affect the surface coverage calculation, but it matters when planning joist spacing and structural support. Follow suitable construction guidance for the complete subframe and fixings.
A worked decking calculation
Suppose you are building a rectangular deck measuring 4.8 metres long by 3.6 metres wide. The boards will run along the 4.8-metre length. Each board is 120mm wide, and you plan to leave a 5mm gap.
Step 1: Convert the deck width
The width to cover is 3.6 metres, which is 3,600mm.
Step 2: Calculate coverage per row
Add the board width and gap:
120mm + 5mm = 125mm.
Step 3: Calculate the number of rows
Using the more precise formula:
(3,600mm + 5mm) ÷ 125mm = 28.84.
You cannot buy or fit 0.84 of a row, so round up. You need 29 rows of decking.
Step 4: Calculate the total linear metres
Each row is 4.8 metres long:
29 rows × 4.8m = 139.2 linear metres.
You therefore need at least 139.2 linear metres before adding waste. If 4.8-metre boards are available and suitable, the basic requirement is 29 full boards. If you use shorter boards, divide the total linear metres by the stock length and then plan where the joints will fall. Joints must be properly supported, and an impractical cutting plan can create extra waste.
How much extra decking should you order?
Do not order the exact mathematical quantity. Cuts around posts, walls, steps and uneven edges can quickly use your spare material. Boards may also contain sections you prefer not to use in a prominent position.
For a straightforward rectangular deck with full-length rows, an allowance of around 5% may be enough. For a design with several cuts, joints or obstacles, 10% is often more practical. Diagonal or detailed layouts can require 15% or more, depending on the design.
In the worked example, adding 10% to 139.2 linear metres gives:
139.2m × 1.10 = 153.12 linear metres.
You would then convert that total into complete stock boards, always rounding up. If using 4.8-metre boards, 153.12 ÷ 4.8 equals 31.9, so you would plan for 32 boards. Confirm available lengths before ordering, as a different length may produce a better cutting plan.
Layouts that need extra planning
The basic formula works well for a plain rectangle, but some layouts need additional calculations:
- Picture-frame borders: calculate the outer border separately, then work out the area inside it.
- Diagonal boards: expect more angled cuts and offcuts, so increase the waste allowance.
- Multiple rectangles: split an L-shaped or stepped deck into simple sections and calculate each one separately.
- Board joints: plan these around the subframe rather than simply adding linear metres.
- Steps and fascias: measure these separately because they are not included in the main deck area.
Do not subtract tiny cut-outs or narrow spaces from your total. The apparent saving is often lost through cuts. For larger openings, such as a substantial planter or pond, calculate the surrounding sections separately.
Common mistakes to avoid
- Using board width without adding the intended gap.
- Mixing metres and millimetres in the same calculation.
- Rounding down instead of up to a complete board.
- Calculating only by square metres and ignoring available board lengths.
- Forgetting boards needed for borders, steps or fascia details.
- Ordering no spare material for cuts or unusable sections.
- Assuming nominal dimensions are the same as finished face dimensions.
Measure the site twice and make a simple board-by-board plan before ordering. If you also need structural timber, discuss your material list rather than assuming the decking quantity covers the supporting frame. K C Fencing and Timber Ltd supplies timber and related materials to trade and DIY customers, but you remain responsible for ensuring the design is suitable and safe.
Request a decking quote
K C Fencing and Timber Ltd supplies decking materials across Wednesbury, Walsall, West Bromwich, Wolverhampton, Dudley, Birmingham and surrounding Black Country towns. West Midlands delivery and free collection from our Wednesbury yard are available. Call 01902 288162 or request a quote with your deck measurements, preferred board size and required lengths.
Need materials?
Same-day and next-day delivery across the West Midlands, or free collection from our Wednesbury yard.
